Exotronic Foldable 200W Portable Solar Solution including a Victron
SmartSolar MPPT 75/15
When camping, parking under shade, or need access to free power to charge your
battery, Exotronic has you covered with a strong but small form-factor
foldable glass solar panel solution. The 200W briefcase is made up from two
100W solar modules using Trina half-cut 23% PERC monocrystalline solar cells
with 9-wire busbars to maximise module efficiency.
Easy Setup and Transport
Weighing only 11.2kg, this panel can be manoeuvred with minimal effort.
These modules include bumpers on the corners and fold-away legs ,
Shade Resistant
Each folded section is wired independently, so if one side is shaded the other
side will still operate.
Premium Cable Set
Also included is an array of premium quality cables to suit any situation:
-
5m 4mm2 PV1-F heavy duty tinned copper (marine) MC4 to 50A grey Anderson cable between the solar panel and solar charge controller (this can be connected directly to your existing DC-DC charger solar input or solar controller) - do not connect the panel directly to a battery without a controller
-
2x 50A grey Anderson tails , to connect to your existing MPPT or PWM solar controller
-
Alligator to 50A grey Anderson with 30A fuse (this can be used to jump start a lithium battery BMS or charge a starter battery when needed)
Protective Canvas Bag Included
The included padded canvas bag helps protect the solar module from
scratches when stored away and includes a carry handle and pocket to
store the cables and controller when not in use.
High-Efficiency Solar Power
Using 23% efficient Trina monocrystalline passivated emitter rear contact
(mono-PERC) square cut cells and the latest 9-wire bus-bar low-loss design,
these panels achieve a high efficiency with a positive power tolerance.
PERC cells provide better performance in low light applications compared to
traditional monocrystalline silicone designs as some of the light that passes
through the cell is bounced back and converted into electricity.
The 9-wire busbar decreases the resistance of the module and carries current
evenly over the whole surface of the cells to ensure that all there are
minimal power losses within the module and significantly reduces uneven cell
heating and hot spots.
Victron SmartSolar 75/15 Bluetooth Solar Charge Controller
For best performance and safety of the solar controller, place the solar
controller near your battery under cover, this reduces heat transfer from the
MPPT to the solar panel and vice-versa.
Bluetooth Smart built-in
The wireless solution to set-up, monitor, update and synchronise SmartSolar
Charge Controllers.
VE.Direct
For a wired data connection to a Color Control GX, other GX products, PC or
other devices
Ultra-fast Maximum Power Point Tracking (MPPT)
Especially in case of a clouded sky, when light intensity is changing
continuously, an ultra-fast MPPT controller will improve energy harvest by up
to 30% compared to PWM charge controllers and by up to 10% compared to slower
MPPT controllers.
Load output
Over-discharge of the battery can be prevented by connecting all loads to the
load output. The load output will disconnect the load when the battery has
been discharged to a pre-set voltage (48V model: interface with a relay).
Alternatively, an intelligent battery management algorithm can be chosen: see
Battery Life. The load output is short circuit proof.
Battery Life: intelligent battery management
When a solar charge controller is not able to recharge the battery to its full
capacity within one day, the result is often that the battery will continually
be cycled between a ‘partially charged’ state and the ‘end of discharge’
state. This mode of operation (no regular full recharge) will destroy a lead-
acid battery within weeks or months. The Battery Life algorithm will monitor
the state of charge of the battery and, if needed, day by day slightly
increase the load disconnect level (i.e. disconnect the load earlier) until
the harvested solar energy is sufficient to recharge the battery to nearly the
full 100%. From that point onwards, the load disconnect level will be
modulated so that a nearly 100% recharge is achieved about once every week.
Programmable battery charge algorithm
See the software section on our website for details
Day/night timing and light dimming option
See the software section on our website for details
Internal temperature sensor
Compensates absorption and float charge voltage for temperature.
